Application
- The FLOREG flow regulator is ideally suited for regulating the flow rates of storm basins and stormwater runoff and contributes to better hydraulic management.
PRINCIPLE AND TECHNICAL DATA
- Provides a constant flow rate, with a variation of less than 5% and a very short response time.
- Mechanical system with progressive closure of the orifice by a diaphragm connected to a float.
- Design to reach the set flow rate as soon as the orifice is loaded.
- Delivered with a stainless steel expansion fixing kit.
- Hydraulic response curve that can be transmitted on request.
- Complies with Technical Opinion 17/03-143 issued by CSTB on controlled flow stormwater runoff.
|
Type
|
Flow l/s
|
H
|
DN
|
A
|
B
|
L1
|
L2
|
|
FL5A
|
5
|
300
|
200
|
250
|
350
|
225
|
450
|
|
FL10A
|
10
|
390
|
200
|
300
|
400
|
293
|
586
|
|
FL15A
|
15
|
465
|
200
|
300
|
450
|
349
|
698
|
|
FL20A
|
20
|
510
|
200
|
350
|
500
|
383
|
766
|
|
FL25B
|
25
|
570
|
300
|
350
|
525
|
428
|
856
|
|
FL30B
|
30
|
600
|
300
|
350
|
550
|
450
|
900
|
|
FL40B
|
40
|
675
|
300
|
400
|
625
|
506
|
1'012
|
|
FL50B
|
50
|
735
|
300
|
400
|
675
|
551
|
1'102
|
|
FL60B
|
60
|
795
|
300
|
450
|
725
|
596
|
1'192
|
|
FL70B
|
70
|
840
|
300
|
450
|
750
|
630
|
1'260
|
|
FL80C
|
80
|
885
|
400
|
450
|
775
|
664
|
1'328
|
|
FL100C
|
100
|
975
|
400
|
500
|
850
|
731
|
1'462
|
|
FL125C
|
125
|
1'065
|
400
|
500
|
925
|
799
|
1'598
|
|
FL150C
|
150
|
1'155
|
400
|
550
|
1'000
|
866
|
1'732
|
|
FL175D
|
175
|
1'215
|
500
|
550
|
1'050
|
911
|
1'822
|
|
FL200D
|
200
|
1'290
|
500
|
600
|
1'100
|
968
|
1'936
|
|
FL250D
|
250
|
1'410
|
500
|
650
|
1'200
|
1'058
|
2'116
|
|
FL300E
|
300
|
1'515
|
600
|
650
|
1'250
|
1'136
|
2'272
|
|
FL350E
|
350
|
1'605
|
600
|
700
|
1'350
|
1'204
|
2'408
|
|
FL400E
|
400
|
1'695
|
600
|
750
|
1'400
|
1'271
|
2'542
|
|
FL450E3
|
450
|
1'770
|
600
|
750
|
1'450
|
1'328
|
2'656
|
Dimensions in mm. For higher flow rates and specific studies: consult us.
H: Maximum water level .
DN: Minimum diameter downstream plastic pipes in free flow.
Non-contractual dimensions
ADVANTAGES
IMPLEMENTATION
On flat and vertical concrete wall.
- Place the adhesive sealing joint on the fixing plate.
- Counter-drill the holes in the template frame at the top and bottom of the regulator.
- Position the expansible plug after each drilling without locking the nut.
- After inserting all the plugs, make a cross clamping. Be careful not to deform the frame.
- After tightening, grout cement mortar if necessary.
